May 15, 2012 · DNSMasq is a lighweight DNS, DHCP and TFTP server provider and is ideal for this case-study. In a couple of return-key-hits from inside your package manager of choice you will have setup a local DNS server for the whole development team to access, keeping all those pesky local domains in one host file, the way it should be. Installation
Setup via DD-WRT Script . 1. In the DD-WRT Administrative Interface, navigate to Setup > Basic Setup. Under Network Address Server Settings (DHCP), set these NordVPN DNS addresses: Static DNS 1 = 103.86.96.100 Static DNS 2 = 103.86.99.100 Static DNS 3 = 0.0.0.0 (default) Use DNSMasq for DHCP = Checked Use DNSMasq for DNS = Checked DHCP When your DD-WRT box is your IPv6-router, see other solutions below for 6to4 tunneling solutions. Enabling IPv6 Support. On the Administration>Management page, enable IPv6 and radvd. Configuring Radvd (if your DD-WRT box is NOT your IPv6-router) Radvd is similar to a DHCP server. Posted: Thu Dec 02, 2010 17:07 Post subject: DNSMasq/Local DNS Setup .. Need Advice. All, Now that I have multiple routers running DD-WRT in my environment, I would like to give the routers a hostname and move away from having to enter the IP addresses every time. Changing DNS in DD-WRT To manually configure your router with our DNS servers’ addresses, in DD_WRT: On the Setup tab under Network Address Server Settings (DHCP) , look for Static DNS 1 and Static DNS 2 . But adding the DD-WRT router hostname to it's own mapping of DNS name → IP results in failed DNS hostname lookups. I'm able to create DNS entries for other hosts on the local network. I did this using by adding entries under Static Leases (under Services → Services → Services Management → DHCP Server → Static Leases ). DD-WRT forces clients to use encyption with 128bit. When encyption is disabled encryption to clients is allwed but not forced. DNS. Add your local/wan DNS server. Setting DNS2 is optional. WINS. Add your local WINS servers. This settings are optional. MTU/MRU. Default: 1436 These settings are very important for correct working connections.
Forced DNS redirection redirects all DNS requests on port 53 to DD-WRT's internal DNSmasq server, even if those requests were pointed directly at an external DNS server. Note that, as discussed in the forum thread, savvy users might still be able to communicate with external DNS servers on non-53 ports. See also: forum thread
DD-WRT forces clients to use encyption with 128bit. When encyption is disabled encryption to clients is allwed but not forced. DNS. Add your local/wan DNS server. Setting DNS2 is optional. WINS. Add your local WINS servers. This settings are optional. MTU/MRU. Default: 1436 These settings are very important for correct working connections. How To Set Up A Repeater Bridge On Your DD-WRT Router. To begin, make sure that the main router has a 192.168.1.X subnet and leases a DHCP address in the same pool. The secondary router must be running DD-WRT. To ensure easy setup, always click Save and not Apply between steps. Reset to Factory Defaults on the secondary DD-WRT router. OP asked "Is there a setting in the DD-WRT router to resolve the hostname to a local IP?", and the answer is yes. A DNS server is specifically for resolving a hostname to an IP. But, unfortunately, you're trying to resolve a hostname on dyndns.org to a local IP, and the response that you will get from a DNS server will be for the public IP that Jan 27, 2011 · DD-WRT firmware provides quite a lot of additional features in a router. However, many of these features make the configuration to be somewhat difficult. DD-WRT DNSMasq Setup and Local DNS
Change your DD-WRT Router DNS server addresses This has to be done only once. Before you switch to our DNS addresses, make sure you write down your current DNS addresses, so you can keep these numbers in case you need to get back to your original settings.
When your DD-WRT box is your IPv6-router, see other solutions below for 6to4 tunneling solutions. Enabling IPv6 Support. On the Administration>Management page, enable IPv6 and radvd. Configuring Radvd (if your DD-WRT box is NOT your IPv6-router) Radvd is similar to a DHCP server. Posted: Thu Dec 02, 2010 17:07 Post subject: DNSMasq/Local DNS Setup .. Need Advice. All, Now that I have multiple routers running DD-WRT in my environment, I would like to give the routers a hostname and move away from having to enter the IP addresses every time. Changing DNS in DD-WRT To manually configure your router with our DNS servers’ addresses, in DD_WRT: On the Setup tab under Network Address Server Settings (DHCP) , look for Static DNS 1 and Static DNS 2 .