Current configuration : 1358 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker !! no aaa new-model memory-size iomem 5 no ip icmp rate-limit unreachable ip cef !! no ip dhcp use vrf connected no ip dhcp conflict
May 02, 2013 · This Is DHCP's Configurtaion on router. no ip dhcp use vrf connected ip dhcp excluded-address 192.168.1.254 ip dhcp excluded-address 192.168.1.1 192.168.1.20 ip dhcp excluded-address 192.168.2.254 ip dhcp excluded-address 192.168.2.1 192.168.2.20 ip dhcp excluded-address 192.168.1.45 ip dhcp excluded-address 192.168.1.71 So the command no ip dhcp use vrf connected should leave interfaces in VRF not considered by DHCP activity. Usage. With the no ip dhcp use vrf connected, if a DHCP request comes from whatever interface here, it will be allocated an IP address from the global DHCP pool Global, without any regard to the VRF of the interface through which the no ip source-route ! ! no ip dhcp use vrf connected ip dhcp excluded-address 192.168.0.0 192.168.0.10 ! ip dhcp pool lan network 192.168.0.0 255.255.255.0 default-router 192.168.0.1 dns-server 192.231.203.132 192.231.203.3 lease infinite ! Feb 22, 2020 · DHCP automatically assigns a device-specific IP address to each device on your router's network, which ensures that no two devices will share an IP address and thus encounter connection errors. Steps Part 1 of 2:
no ip dhcp pool dhcppool no ip dhcp use vrf connected no ip dhcp excluded-address 192.168.10.1 192.168.10.254 no ip dhcp pool STATIC-SRV1 no ip dhcp pool STATIC-SRV2 no ip dhcp pool STATIC-SRV3 no ip dhcp pool STATIC-SRV4 no ip dhcp pool STATIC-SRV5 no ip dhcp pool STATIC-SRV6 no ip dhcp pool STATIC-SRV7 no ip dhcp pool STATIC-SRV8 no ip dhcp
no ip dhcp use vrf connected ip dhcp excluded-address 192.168.1.1! ip dhcp pool internal-net import all network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 domain-name its-control.com! ip interface Vlan1 no ip address ! interface Async1 no ip address encapsulation slip ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 dhcp !! no ip http server no ip http secure-server ip nat inside source list 101 interface FastEthernet0 overload ! access-list 101 permit ip 10.0.0.0 0.0.0.255 any !!!!! control-plane !! line con 0 line 1 interface tunnel200 ! ip vrf forward cust2-vrf ! ip address 172.17.20.1 255.255.255.0 ! ip mtu 1400 ! ip tcp adjust-mss 1360 ! tunnel source fast0/0 ! tunnel destination 104.57.98.11 ! tunnel vrf outside-vrf ! tunnel protection ipsec profile cust1-ipsec-prof ! descr Tunnel interface Cust-2 ! 28.4 Route ManagementWhen routing is enabled, the switch discovers the best route to a packet’s destination address by exchanging routing information with other devices. IP routing is disabled by default. The following sections describes routing fe
first, try resetting the router to factory defaults, there should be a reset button on back. next enter the router by typing the ip address of the default gateway in your web browser username/pass
ip subnet-zero ip cef! no ip dhcp use vrf connected! ip tcp synwait-time 10 no ip ips deny-action ips-interface! crypto isakmp policy 1 encr 3des authentication pre-share group 2 crypto isakmp key ***** address 81.x.x.x crypto isakmp invalid-spi-recovery!! crypto ipsec transform-set 3DES-SHA esp-3des esp-sha-hmac R1#SHOW RUN | sec ip dhcp no ip dhcp use vrf connected ip dhcp pool DONDRUJA network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 option 150 ip 192.168.1.1 dns-server 8.8.8.8 lease 2 ip dhcp pool PC2 Ayup. R1 Fa0/0 -> R1 Fa0/1! hostname R1 ! vrf definition V1 rd 1:1 ! address-family ipv4 exit-address-family ! vrf definition V2 rd 2:2 ! address-family ipv4 exit-address-family ! ip dhcp pool V1_POOL vrf V1 network 1.0.0.0 255.255.255.0 default-router 1.0.0.1 ! interface FastEthernet0/0 vrf forwarding V1 ip address 1.0.0.1 255.255.255.0 ! interface FastEthernet0/1 vrf forwarding V2 ip address Hi all, is there a particular correct way to have one VRF with two associated subnets, and have a DHCP server for each VRF? I found that I cannot assign two dhcp pools to the same VRF, but I can associate multiple subinterfaces with different subnets to the same VRF. Can I use ip-helper somehow instead? I need the router to also serve DHCP to